Statuary (Fountain) Pump Instructions
Mag-driven SICCE statuary pumps with built-in filters and flow control devices. Ideal for statues and fountains, but can also be used to circulate the water for a small pond up to 300 gallons (provided the pond does not contain a waterfall or fish). Tubing not included with statuary pumps. Made in Italy; 2 Year Warranty.
Before carrying out any operations on the pump, disconnect power supply to all the electrical devices located under the water.
Do not install if the cable or the pump have been damaged in any way. The power cable of this appliance cannot be replaced, if it is damaged the appliance must be scrapped.
This product complies with the current safety standards. Check the voltage marked on the pump and ensure that it corresponds to the main voltage.
THIS PUMP MUST NOT OPERATE WITHOUT WATER. THE PUMP MAY BE USED IN WATER WITH A TEMPERATURE NO HIGHER THAN 35°C.
See summary of all Statuary Fountain pumps
Maintenance
These statuary pumps are pumps with exceptional performance, ideal for use in small spaces thanks to their compact dimensions. Their maintenance requirements are minimum, but it is very important to maintain the pump to ensure correct operation. Before handling these pumps, turn off electrical power of any equipment immersed in water.
Read More
Mi-Mouse
The Mi-Mouse pump has a fixed water output pope 10mm high with an external diameter of 13mm; this allows for the connection of flexible tubing with a 1/2" diameter. The pump is equipped with a series of four vibration-damping rubber pads which are useful for elimination any noise due to vibration of the pump. The water flow rate may be varied by adjusting the flow regulator, which enables it to be controlled according to each user's requirements.
Maintenance
Every 1–2 months remove the front and gently remove the rotor. Wash all the parts in lukewarm water, gently removing any accumulated scale. Reassemble the parts in inverse order. The side suction grills also need cleaning periodically to allow a continuous, constant passage of water; use a small brush to remove all the scale deposits.
Micra & Micra-Plus
For optimal function a minimum water height of approximately 2 cm is suggested. The pump may be connected with flexible 1/2" tubing.
Capacity may be controlled by using the flow monitor system which allows for a precise incremental adjustment, depending on the need.
Maintenance
These pumps are endowed with a small filter which must be cleansed regularly or when water flow diminishes considerably. To clean, simply remove front case, rinse filtering material and reassemble using same procedure in reverse. Every three months, clean all other parts in warm water, delicately removing calcium deposits.
Nova
The pump features a ½" outlet which allows for connection to 1/2" tubing. For use in which a wide support area is necessary, it is possible to use the folding support suckers which are part of the pump. To open the support system, simply rotate it to close it, it is necessary to rotate it in the opposite direction by exerting certain effort.The pump is also endowed with a flow regulator which allows one to vary the capacity for a specific dose, as required by user.
Maintenance
Every 2–3 months remove the front grill, delicately take out rotor and wash it entirely in warm water, taking out any calcareous deposits. Reassemble everything in reverse order.
Idra
The pump features a 3/4" outlet which allows for the connection to 3/4" flexible tubing. When a wide support area is necessary, it is possible to use the folding support suckers which are part of the pump. To open the support system, simply rotate it to close it; it may be necessary to rotate it in the opposite direction by applying effort.The pump is also endowed with a flow regulator which allows one to vary the capacity for a specific dose, as required by user.
Maintenance
Every 2–3 months remove the front grill, delicately take out rotor and wash it entirely in warm water, taking out any calcareous deposits. Reassemble everything in reverse order.
Extrema
The pump EXTREMA features a 3/4" threaded outlet which allows the connection to 3/4" flexible tubing. When a wide support area is necessary, it is possible to use the folding support sucks which are part of the pump. To open the support, simply rotate it in the opposite direction by applying force. The pump is also endowed with a flow regulator which allows one to vary the water flow.
Maintenance
Remove the front cover as well as the prechamber every 2–3 months. Then, carefully withdraw the rotor and the cam. Wash with lukewarm water and remove possible calcareous deposits. Reassemble everything in reverse order, making sure that the reference arrow located on the prechamber faces up.
